Published at Thursday, February 28th, 2019 - 02:54:33 AM. Fence. By Floretta Roth.
Recommended Time Frame for Cleaning a Wood Fence: * For maximum results we recommend that you clean/re-stain your wood fence once every 3-5 years. Cleaning: IF you have a cedar fence, you may notice that it will begin to turn a grayish color or the paint/stain will begin to lose its brightness and regardless of what kind of wood fence you have, you may notice a mold begin to develop on the fence. This section of the article will explain how to take care of these problems and get your wood fence looking new again! If you decided to use plastic sheeting to protect your grass, you will want to lay that on the ground underneath the fence prior to starting any cleaning. (Using plastic sheeting will protect your grass from any harmful chemicals that may be in the cleaning solutions). A mixture of 1 part bleach and 2 parts water is very common when cleaning wood fences; however, you may also purchase wood cleaning solution from your local hardware store. What you will want to do first is apply the cleaning solution to the fence and allow it to soak in until you notice that the fence is becoming brighter and/or clean. You will then want to spray the fence off with a water hose (use a power washer for removing old paint or tough stains - make sure power washer is on the widest spray setting and held about 12 inches away from fence). After the fence has been cleaned and sprayed off you will want to allow it to air dry. If it still needs cleaning in certain spots after it dries, repeat the above mentioned process. Once the fence is clean and dry you are ready to apply a strain. (If you do not wish to stain a certain color, you can use a wood sealant to ensure that the fence will look new for a long time). NOTE: DO NOT USE PAINT ON YOUR WOOD FENCE, INSTEAD USE A STAIN. Properly apply the strain and allow the stain to dry. Your wood fence should now look beautiful and brand new. If you apply this process at least every 3 - 5 years, your wood fence will look beautiful and brand new for a long time!
Do It Yourself Fencing Repair - Replacing Posts in Fence Made Easy Do it yourself fencing repair can be a challenge for the inexperienced but it doesnt have to be. Knowing times are tough and as a thirty year veteran I will try to make fencing repair, changing rotted fencing posts and replacing panels in your fence doable for those who like to do it yourself and save money. I will address: * Do it Yourself Fencing Repair * Replacing rotted Fence Post * Cedar fence Fence Post * Treated Wood Post * Galvanized Metal Fence post * Changing a Wood Fence Picket * Adding or Changing Fence Rail There are as many How to Wood Fence and Fencing Repair as there are nails in fence pickets. The way that I describe here has worked for me here in the Dallas Texas metro area for many years. Do it yourself fencing repair: Is easy if you go about it the right way but is very hard if you go about it the wrong way and can get very frustrating and costly. Replacing Rotted Fence Post: Replacing posts in a Fence is one of the hardest things about fencing repair. I have seen DIYers try everything to get broken fence post out of the ground. One of my favorites is what I call the Grand Canyon. This is when a DIY will dig a hole so big around the fence post that they almost need a cement truck to bring in enough concrete to fill it. Have you ever dug a hole for a fence post? If so use the concept of digging a 8 inch diameter hole for a fence post against the concrete of the old fence post about 2-2 1/2 feet deep. Then take a sharp shooter shovel to clear a little dirt from each side of the concrete. Use post hole digger to remove the little bit of dirt that you loosened from the post hole. You now have a hole that is deep enough that with a little effort you can use a rock bar to lever the broken post and concrete into the hole you just dug so that it will be easy to lift out. Put the new pole in the hole, take the old hard concrete and use as filler in the hole and put as much premixed wet concrete in the hole as needed to fill to the ground level then plumb the pole with a level. You can then wait 24 hours for the concrete to harden around the new fence post the nail the fence panels to it or you can go ahead nail the old or new fence panels to it, re-level the post and then use an old fence board to support it. If you would like the easier way out then you can install a new fence post in next to the existing so that you do not have to dig the wood post out.
Any content, trademark’s, or other material that might be found on the Proxifeed website that is not Proxifeed’s property remains the copyright of its respective owner/s. In no way does Proxifeed claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.