Published at Wednesday, February 27th, 2019 - 14:03:40 PM. Fence. By Bevis Perrier.
What is an underground dog fence? An underground dog fence is a system consisting of a radio transmitter, wire that acts as a transmitting antenna and a collar with a receiver that picks up the radio signal from the fence when your dog gets too close. When your dog enters the warning area near the wire the collar beeps warning him to stay back. If he continues to move toward the wire he will receive a static shock or correction. Some systems have progressive corrections so that the closer the dog progresses toward the wire the stronger the static shock he receives. There is some controversy about the humane aspect of delivering a shock to an animal to deter him. Most experts agree however that when an underground dog fence is properly installed and the dog is properly trained to the fence that these systems are very humane and safe. Consider the alternative if your dog runs out into traffic or gets lost. There is some chance of your dog being traumatized by the shock of he is improperly trained and/or the correction levels are too high for your particular dogs size and temperament. Proper training is critical to success with these systems. Yes, it is true that your dog, hopefully, will not like receiving the shock no more than you like touching a door knob and getting a static shock. This is his incentive to avoid the boundary. While the shock is uncomfortable it is not in itself dangerous to the animal. Most systems have automatic shut offs if the animal does not move out of the correction zone to protect him from over correction. Compared to a traditional fence an underground dog fence is fairly easy to install and should take less than a day with most applications. The hardest part of the installation is burying the wire. I offer four methods of burying the wire. The first is to use a straight edge spade shovel and use it to dig down about 3 inches and create a V-shaped trench to lay the wire in. The simply press the sod or dirt back in place. This is the most difficult and time consuming method. The second way is to use a gas powered lawn edger to cut a 3 inch deep trench. Lay the wire in the trench and replace the displaced dirt and press into place. The third method is to rent a trencher with a cable installation attachment. The trencher will cut the trench and lay the wire at the same time. The fourth method is to not bury the wire at all. Instead you can simple lay the wire above ground and use Pet Fence Staples to hold it in place. This method works well for low traffic areas and in grassy areas where the wire will lay deep in the turf. If you have to cross a driveway or sidewalk with the wire you will need to use a masonry blade to cut a groove in the concrete or asphalt and then use caulk to seal the wire into place. There are many factors involved in choosing the right underground dog fence system. Some of these factors are discussed below. Later on Ill make specific recommendations based on these factors. Wireless dog fences are not considered in this discussion.
Do It Yourself Fencing Repair - Replacing Posts in Fence Made Easy Do it yourself fencing repair can be a challenge for the inexperienced but it doesnt have to be. Knowing times are tough and as a thirty year veteran I will try to make fencing repair, changing rotted fencing posts and replacing panels in your fence doable for those who like to do it yourself and save money. I will address: * Do it Yourself Fencing Repair * Replacing rotted Fence Post * Cedar fence Fence Post * Treated Wood Post * Galvanized Metal Fence post * Changing a Wood Fence Picket * Adding or Changing Fence Rail There are as many How to Wood Fence and Fencing Repair as there are nails in fence pickets. The way that I describe here has worked for me here in the Dallas Texas metro area for many years. Do it yourself fencing repair: Is easy if you go about it the right way but is very hard if you go about it the wrong way and can get very frustrating and costly. Replacing Rotted Fence Post: Replacing posts in a Fence is one of the hardest things about fencing repair. I have seen DIYers try everything to get broken fence post out of the ground. One of my favorites is what I call the Grand Canyon. This is when a DIY will dig a hole so big around the fence post that they almost need a cement truck to bring in enough concrete to fill it. Have you ever dug a hole for a fence post? If so use the concept of digging a 8 inch diameter hole for a fence post against the concrete of the old fence post about 2-2 1/2 feet deep. Then take a sharp shooter shovel to clear a little dirt from each side of the concrete. Use post hole digger to remove the little bit of dirt that you loosened from the post hole. You now have a hole that is deep enough that with a little effort you can use a rock bar to lever the broken post and concrete into the hole you just dug so that it will be easy to lift out. Put the new pole in the hole, take the old hard concrete and use as filler in the hole and put as much premixed wet concrete in the hole as needed to fill to the ground level then plumb the pole with a level. You can then wait 24 hours for the concrete to harden around the new fence post the nail the fence panels to it or you can go ahead nail the old or new fence panels to it, re-level the post and then use an old fence board to support it. If you would like the easier way out then you can install a new fence post in next to the existing so that you do not have to dig the wood post out.
Any content, trademark’s, or other material that might be found on the Proxifeed website that is not Proxifeed’s property remains the copyright of its respective owner/s. In no way does Proxifeed claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.